General Welding Questions
RSS | Subscribe | Contact Us | Advertise | About Us
Page 1 of 854 1231151101501 ... LastLast
Threads 1 to 25 of 21343

Forum: General Welding Questions

If you are new to the welding industry or just have general questions and do not know where to ask them, this is the forum!

  1. Rod oven alternatives

    Started by Welding Riddler18, 10-17-2017 09:24 PM
    2 Pages
    1 2
    • Replies: 32
    • Views: 862
    Today, 11:23 AM Go to last post
  2. Misc. Welding 2:

    Started by HungryTurtle, Today 10:55 AM
    • Replies: 2
    • Views: 3
    Today, 11:18 AM Go to last post
  3. Fabtech 2017

    Started by vwguy3, Yesterday 08:28 PM
    • Replies: 15
    • Views: 218
    Today, 11:00 AM Go to last post
  4. Introduction, shop layout and other questions...

    Started by PatriceL, 09-27-2017 10:55 PM
    8 Pages
    1 2 3 4 5 ... 8
    • Replies: 197
    • Views: 5,777
    Today, 10:42 AM Go to last post
  5. Advice for father...

    Started by dawicks, 10-10-2017 12:18 AM
    3 Pages
    1 2 3
    • Replies: 50
    • Views: 1,671
    Today, 10:18 AM Go to last post
  6. How To Fill Holes With Stick?

    Started by abrogard, Yesterday 10:08 PM
    • Replies: 19
    • Views: 311
    Today, 10:13 AM Go to last post
    • Replies: 3
    • Views: 133
    Today, 10:08 AM Go to last post
  7. practice stick welding

    Started by monirh, 08-17-2017 01:54 PM
    • Replies: 16
    • Views: 986
    Today, 09:48 AM Go to last post
  8. Miller dialarc ac dc 250

    Started by davezelonis, 10-09-2017 09:02 PM
    2 Pages
    1 2
    • Replies: 39
    • Views: 829
    Today, 08:27 AM Go to last post
  9. Cold welding space!

    Started by Blocker, Yesterday 10:45 PM
    • Replies: 3
    • Views: 163
    Today, 08:18 AM Go to last post
  10. Viking, Miller, Optrel Optics

    Started by Seawalker, Yesterday 09:24 PM
    • Replies: 3
    • Views: 97
    Yesterday, 10:01 PM Go to last post
  11. Why are all the new guys hung up on tig?

    Started by Jolly Roger, 02-20-2008 07:36 PM
    10 Pages
    1 2 3 4 5 ... 10
    • Replies: 235
    • Views: 43,107
    Yesterday, 09:29 PM Go to last post
  12. 75/25 Mix (C25)

    Started by matyboom808, 10-19-2017 10:27 PM
    • Replies: 7
    • Views: 379
    Yesterday, 09:11 PM Go to last post
    • Replies: 14
    • Views: 425
    Yesterday, 07:53 PM Go to last post
  13. can I use copper (or brass) as a backing plate ?

    Started by olek, Yesterday 12:24 PM
    backplate, copper
    • Replies: 15
    • Views: 276
    Yesterday, 07:05 PM Go to last post
  14. Flux core wire

    Started by AllDodge, 10-15-2017 06:40 PM
    2 Pages
    1 2
    • Replies: 29
    • Views: 821
    Yesterday, 06:37 PM Go to last post
  15. Miller Recommendation Mig Welder

    Started by Can'tWeld, 03-09-2017 08:14 PM
    2 Pages
    1 2
    • Replies: 42
    • Views: 2,806
    Yesterday, 12:21 PM Go to last post
  16. pipe welding job after school?

    Started by 2005tritontr186, Yesterday 11:02 AM
    • Replies: 1
    • Views: 125
    Yesterday, 12:01 PM Go to last post
  17. Table Top Question

    Started by rmyers, 10-15-2017 07:50 PM
    • Replies: 20
    • Views: 792
    10-20-2017, 10:15 PM Go to last post
  18. verbal directions?

    Started by tbirkey, 10-20-2017 05:20 PM
    • Replies: 5
    • Views: 278
    10-20-2017, 10:07 PM Go to last post
  19. Miller Big 40 and 44G Question

    Started by kjemison1966, 10-19-2017 09:36 PM
    • Replies: 2
    • Views: 149
    10-20-2017, 08:50 PM Go to last post
  20. Need suggestions for a beginner welding project

    Started by gmt, 10-12-2017 11:46 AM
    • Replies: 23
    • Views: 785
    10-20-2017, 12:42 PM Go to last post
    • Replies: 9
    • Views: 263
    10-19-2017, 10:16 PM Go to last post
  21. HTP Invertig 221 water or air cooled

    Started by formernuke, 10-19-2017 12:56 PM
    • Replies: 9
    • Views: 217
    10-19-2017, 08:53 PM Go to last post
  22. Black Friday predictions?

    Started by yellowfin, 10-18-2017 07:49 PM
    • Replies: 5
    • Views: 417
    10-19-2017, 08:52 PM Go to last post

Forum Information and Options

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
RSS | Home | Penton Media | Contact Us | Subscribe | For Advertisers | Terms of Use | Privacy Statement