General Welding Questions
RSS | Subscribe | Contact Us | Advertise | About Us
Page 1 of 859 1231151101501 ... LastLast
Threads 1 to 25 of 21459

Forum: General Welding Questions

If you are new to the welding industry or just have general questions and do not know where to ask them, this is the forum!

    • Replies: 4
    • Views: 10
    Today, 09:23 PM Go to last post
    • Replies: 3
    • Views: 109
    Today, 09:00 PM Go to last post
  1. Is there any other women in this site???

    Started by aprilspence, 11-01-2016 02:16 PM
    5 Pages
    1 2 3 4 5
    • Replies: 104
    • Views: 8,155
    Today, 08:50 PM Go to last post
  2. Welding square tubing together

    Started by davezelonis, 11-14-2017 03:06 PM
    4 Pages
    1 2 3 4
    • Replies: 94
    • Views: 2,982
    Today, 06:40 PM Go to last post
    • Replies: 2
    • Views: 78
    Today, 06:16 PM Go to last post
  3. Welding table bowed upwards

    Started by Steve Shimanek, 11-20-2017 01:18 PM
    2 Pages
    1 2
    • Replies: 27
    • Views: 946
    Today, 04:18 PM Go to last post
  4. Need to buy pipe coupons

    Started by welder19, 11-19-2017 03:47 PM
    2 Pages
    1 2
    • Replies: 25
    • Views: 704
    Today, 03:55 PM Go to last post
  5. Dedicated Circuit for Welder

    Started by dawicks, 11-08-2017 06:49 PM
    • Replies: 20
    • Views: 672
    Today, 03:47 PM Go to last post
  6. Welding a cast iron engine block

    Started by crustyrusty, 11-19-2017 10:40 PM
    2 Pages
    1 2
    • Replies: 30
    • Views: 917
    Today, 02:25 PM Go to last post
    • Replies: 20
    • Views: 728
    Today, 11:31 AM Go to last post
  7. Questions about local supplies.

    Started by mrmiz, 11-16-2017 06:55 PM
    • Replies: 11
    • Views: 441
    Today, 09:36 AM Go to last post
  8. Another welder advice question.

    Started by Alabass, 11-19-2017 05:30 PM
    • Replies: 2
    • Views: 259
    Yesterday, 11:32 PM Go to last post
  9. Full penetration s.s. tube welding

    Started by Brainfarth, Yesterday 11:15 AM
    • Replies: 8
    • Views: 284
    Yesterday, 11:25 PM Go to last post
  10. Modified pipeliner helmet........

    Started by Murphy's law, 01-28-2015 12:45 PM
    2 Pages
    1 2
    • Replies: 28
    • Views: 4,184
    Yesterday, 10:26 PM Go to last post
  11. Porosity at beginning of weld

    Started by davezelonis, 11-19-2017 09:16 PM
    2 Pages
    1 2
    • Replies: 27
    • Views: 696
    Yesterday, 02:48 PM Go to last post
  12. Miller

    Started by Bzeis, 11-15-2017 04:46 PM
    2 Pages
    1 2
    • Replies: 33
    • Views: 1,102
    Yesterday, 11:55 AM Go to last post
  13. Any better options for 400amp clamps?

    Started by One1, 11-20-2017 07:39 PM
    • Replies: 13
    • Views: 375
    Yesterday, 10:45 AM Go to last post
  14. What to use to clean torch guts?

    Started by One1, 11-19-2017 06:23 PM
    • Replies: 15
    • Views: 470
    Yesterday, 06:32 AM Go to last post
  15. Introduction, shop layout and other questions...

    Started by PatriceL, 09-27-2017 10:55 PM
    9 Pages
    1 2 3 4 5 ... 9
    • Replies: 211
    • Views: 7,414
    11-20-2017, 02:09 PM Go to last post
  16. Tools for cleaning rust & millscale

    Started by olek, 11-15-2017 03:50 PM
    • Replies: 18
    • Views: 865
    11-20-2017, 02:09 PM Go to last post
  17. Spool gun vs tig

    Started by kevnj, 10-13-2017 11:35 AM
    • Replies: 20
    • Views: 1,253
    11-20-2017, 01:55 PM Go to last post
    • Replies: 16
    • Views: 754
    11-20-2017, 12:42 PM Go to last post
  18. Respirator Advice

    Started by vtwin86, 10-30-2012 11:20 PM
    3 Pages
    1 2 3
    • Replies: 64
    • Views: 14,696
    11-19-2017, 08:09 AM Go to last post
  19. MIG Feed issues

    Started by Hypervisor, 11-18-2017 08:02 PM
    • Replies: 4
    • Views: 246
    11-19-2017, 12:03 AM Go to last post
  20. Found Lincoln Ac/Dc tombstone

    Started by davezelonis, 11-02-2017 07:24 PM
    10 Pages
    1 2 3 4 5 ... 10
    • Replies: 242
    • Views: 5,334
    11-18-2017, 11:09 PM Go to last post

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
RSS | Home | Penton Media | Contact Us | Subscribe | For Advertisers | Terms of Use | Privacy Statement