General Welding Questions
RSS | Subscribe | Contact Us | Advertise | About Us
Page 1 of 859 1231151101501 ... LastLast
Threads 1 to 25 of 21456

Forum: General Welding Questions

If you are new to the welding industry or just have general questions and do not know where to ask them, this is the forum!

  1. Full penetration s.s. tube welding

    Started by Brainfarth, Today 11:15 AM
    • Replies: 4
    • Views: 50
    Today, 01:18 PM Go to last post
  2. Is there any other women in this site???

    Started by aprilspence, 11-01-2016 02:16 PM
    4 Pages
    1 2 3 4
    • Replies: 95
    • Views: 7,306
    Today, 12:24 PM Go to last post
  3. Miller

    Started by Bzeis, 11-15-2017 04:46 PM
    2 Pages
    1 2
    • Replies: 33
    • Views: 1,025
    Today, 11:55 AM Go to last post
  4. Welding a cast iron engine block

    Started by crustyrusty, 11-19-2017 10:40 PM
    2 Pages
    1 2
    • Replies: 26
    • Views: 642
    Today, 10:56 AM Go to last post
  5. Any better options for 400amp clamps?

    Started by One1, Yesterday 07:39 PM
    • Replies: 13
    • Views: 288
    Today, 10:45 AM Go to last post
  6. Porosity at beginning of weld

    Started by davezelonis, 11-19-2017 09:16 PM
    2 Pages
    1 2
    • Replies: 25
    • Views: 547
    Today, 09:56 AM Go to last post
  7. What to use to clean torch guts?

    Started by One1, 11-19-2017 06:23 PM
    • Replies: 15
    • Views: 440
    Today, 06:32 AM Go to last post
  8. Need to buy pipe coupons

    Started by welder19, 11-19-2017 03:47 PM
    • Replies: 16
    • Views: 467
    Today, 05:36 AM Go to last post
  9. Welding table bowed upwards

    Started by Steve Shimanek, Yesterday 01:18 PM
    • Replies: 9
    • Views: 349
    Yesterday, 10:18 PM Go to last post
  10. Modified pipeliner helmet........

    Started by Murphy's law, 01-28-2015 12:45 PM
    2 Pages
    1 2
    • Replies: 26
    • Views: 4,083
    Yesterday, 03:57 PM Go to last post
  11. Introduction, shop layout and other questions...

    Started by PatriceL, 09-27-2017 10:55 PM
    9 Pages
    1 2 3 4 5 ... 9
    • Replies: 211
    • Views: 7,367
    Yesterday, 02:09 PM Go to last post
  12. Tools for cleaning rust & millscale

    Started by olek, 11-15-2017 03:50 PM
    • Replies: 18
    • Views: 840
    Yesterday, 02:09 PM Go to last post
  13. Spool gun vs tig

    Started by kevnj, 10-13-2017 11:35 AM
    • Replies: 20
    • Views: 1,219
    Yesterday, 01:55 PM Go to last post
    • Replies: 16
    • Views: 735
    Yesterday, 12:42 PM Go to last post
    • Replies: 16
    • Views: 592
    11-19-2017, 10:54 PM Go to last post
  14. Another welder advice question.

    Started by Alabass, 11-19-2017 05:30 PM
    • Replies: 1
    • Views: 181
    11-19-2017, 07:08 PM Go to last post
  15. Respirator Advice

    Started by vtwin86, 10-30-2012 11:20 PM
    3 Pages
    1 2 3
    • Replies: 64
    • Views: 14,657
    11-19-2017, 08:09 AM Go to last post
  16. MIG Feed issues

    Started by Hypervisor, 11-18-2017 08:02 PM
    • Replies: 4
    • Views: 225
    11-19-2017, 12:03 AM Go to last post
  17. Found Lincoln Ac/Dc tombstone

    Started by davezelonis, 11-02-2017 07:24 PM
    10 Pages
    1 2 3 4 5 ... 10
    • Replies: 242
    • Views: 5,288
    11-18-2017, 11:09 PM Go to last post
  18. New rig, got a question......

    Started by One1, 11-17-2017 07:36 PM
    • Replies: 9
    • Views: 484
    11-18-2017, 06:06 PM Go to last post
  19. Another which welder to get!

    Started by noJuan, 11-17-2017 06:58 PM
    • Replies: 6
    • Views: 343
    11-18-2017, 05:05 PM Go to last post
  20. Why does Stainless seem to retain heat?

    Started by OCD, 11-15-2017 10:38 PM
    • Replies: 11
    • Views: 495
    11-18-2017, 02:56 PM Go to last post
  21. Opportunity to use strong arc force, as 100%?

    Started by olek, 11-13-2017 06:47 AM
    • Replies: 24
    • Views: 806
    11-18-2017, 09:58 AM Go to last post
  22. Aluminum welding with MIG gun?

    Started by breavis, 11-16-2017 08:01 PM
    • Replies: 15
    • Views: 531
    11-17-2017, 11:12 PM Go to last post
  23. got an odd stick welder

    Started by camy, 11-17-2017 07:11 PM
    • Replies: 2
    • Views: 243
    11-17-2017, 10:15 PM Go to last post

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
RSS | Home | Penton Media | Contact Us | Subscribe | For Advertisers | Terms of Use | Privacy Statement