CP200 on single phase
RSS | Subscribe | Contact Us | Advertise | About Us
Results 1 to 7 of 7
  1. #1
    Join Date
    Feb 2014
    Location
    Iowa
    Posts
    455

    CP200 on single phase

    Well, got the haas-kamp conversion wrapped up on a cp200 for my dad.

    A little off on the voltage, Lincoln app recommends 300 ipm on .045 wire, @ 23V.

    Not sure what voltage drop should be from open circuit to voltage while welding, but indicated voltage is 26V looks like I'm running 20V while burning.

    Had a little much on the WFS, she was pushing 250A, but it was too much wire.

    Just blasting away on some 3/8 scrap.

    A few screen shots here, try and post a video if I can figure out how when I get back on WiFi.

    Name:  Screenshot_20170105-185230.jpg
Views: 143
Size:  57.0 KB

    Dropped the WFS down a little

    Name:  Screenshot_20170105-185258.jpg
Views: 130
Size:  57.0 KB

    Picked up 3 of these little girls for $125/each with 10E wire feeders.

    Pretty pleased with the results.
    Miller Dynasty 350
    Miller CP300
    Miller CP200
    Lincoln Idealarc 250/250
    Smith torch
    Lagun FTV-2
    Kent 13x40 TRL lathe
    Bunch of other metal cutting tools

  2. #2
    Join Date
    Jan 2008
    Location
    Lansing, MI
    Posts
    6,133

    Re: CP200 on single phase

    I'll get that stuff out to you this weekend man. Been running like crazy since the holidays

  3. #3
    Join Date
    Feb 2014
    Location
    Iowa
    Posts
    455

    Re: CP200 on single phase

    No rush man, I appreciate it!
    Miller Dynasty 350
    Miller CP300
    Miller CP200
    Lincoln Idealarc 250/250
    Smith torch
    Lagun FTV-2
    Kent 13x40 TRL lathe
    Bunch of other metal cutting tools

  4. #4
    Join Date
    Jan 2008
    Location
    Lansing, MI
    Posts
    6,133

    Re: CP200 on single phase

    No problem. I'll even write myself a note so I don't forget. I was out there for a minute today, know where the stuff is.

  5. #5
    Join Date
    Feb 2014
    Location
    Iowa
    Posts
    455

    Re: CP200 on single phase

    Couple beads on 1/4" material. I know travel speed needs improvement, didn't spend much time dialing it in, just doing some function testing.

    Cut and etch tomorrow.
    Name:  20170105_202846.jpg
Views: 99
Size:  68.5 KB

    Name:  20170105_202900.jpg
Views: 97
Size:  66.6 KB
    Miller Dynasty 350
    Miller CP300
    Miller CP200
    Lincoln Idealarc 250/250
    Smith torch
    Lagun FTV-2
    Kent 13x40 TRL lathe
    Bunch of other metal cutting tools

  6. #6
    Join Date
    Jan 2008
    Location
    Lansing, MI
    Posts
    6,133

    Re: CP200 on single phase

    They look good from here!

  7. #7
    Join Date
    Feb 2014
    Location
    Iowa
    Posts
    455

    Re: CP200 on single phase

    Etched at two places. Not bad for the first runs.
    Name:  20170106_112209.jpg
Views: 72
Size:  52.2 KB

    Name:  20170106_112209.jpg
Views: 72
Size:  52.2 KB
    Attached Images Attached Images  
    Miller Dynasty 350
    Miller CP300
    Miller CP200
    Lincoln Idealarc 250/250
    Smith torch
    Lagun FTV-2
    Kent 13x40 TRL lathe
    Bunch of other metal cutting tools

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
RSS | Home | Penton Media | Contact Us | Subscribe | For Advertisers | Terms of Use | Privacy Statement