General Welding Questions
RSS | Subscribe | Contact Us | Advertise | About Us
Page 1 of 872 1231151101501 ... LastLast
Threads 1 to 25 of 21787

Forum: General Welding Questions

If you are new to the welding industry or just have general questions and do not know where to ask them, this is the forum!

    • Replies: 2
    • Views: 78
    Today, 07:14 AM Go to last post
  1. Flame straightening

    Started by biguglydave, 03-20-2019 09:56 PM
    2 Pages
    1 2
    • Replies: 47
    • Views: 1,432
    Today, 04:04 AM Go to last post
    • Replies: 66
    • Views: 1,595
    Today, 02:14 AM Go to last post
  2. Metal cutting circular saw blades

    Started by biguglydave, Yesterday 10:39 PM
    • Replies: 0
    • Views: 53
    Yesterday, 10:39 PM Go to last post
    • Replies: 28
    • Views: 557
    Yesterday, 09:51 PM Go to last post
  3. Help With School Project

    Started by DaFox, 03-15-2019 01:05 PM
    • Replies: 14
    • Views: 581
    Yesterday, 09:30 PM Go to last post
  4. Check out my new scooter

    Started by searcyfarms, 03-06-2019 11:08 PM
    4 Pages
    1 2 3 4
    • Replies: 87
    • Views: 1,796
    Yesterday, 08:40 PM Go to last post
  5. Blending / finishing aluminum

    Started by akpolaris, Yesterday 08:17 AM
    • Replies: 4
    • Views: 133
    Yesterday, 08:12 PM Go to last post
    • Replies: 7
    • Views: 228
    Yesterday, 07:36 PM Go to last post
  6. $200 new mini dewalt grinder review - DWE43244N = JUNK/JOKE/TRASH

    Started by 123weld, 03-22-2019 08:11 PM
    2 Pages
    1 2
    • Replies: 29
    • Views: 705
    Yesterday, 05:05 PM Go to last post
  7. Any info on an old Unibraze wire feeder?

    Started by phoenix02, 03-23-2019 10:25 PM
    • Replies: 0
    • Views: 69
    03-23-2019, 10:25 PM Go to last post
  8. Fuel transfer tank build

    Started by flushcut, 03-15-2019 07:32 PM
    3 Pages
    1 2 3
    • Replies: 63
    • Views: 1,435
    03-23-2019, 10:09 PM Go to last post
  9. Cutting angle iron at 45

    Started by n00b, 03-14-2019 10:09 AM
    3 Pages
    1 2 3
    • Replies: 53
    • Views: 1,870
    03-23-2019, 09:38 PM Go to last post
  10. Fixing up a trailer

    Started by phoenix02, 03-18-2019 09:20 PM
    • Replies: 23
    • Views: 732
    03-23-2019, 09:34 PM Go to last post
  11. FCAW wire selection?

    Started by Q-Fab, 03-22-2019 03:59 PM
    • Replies: 8
    • Views: 279
    03-23-2019, 07:31 PM Go to last post
  12. Plasma cutting question

    Started by russ69coupe, 03-22-2019 03:11 AM
    • Replies: 15
    • Views: 472
    03-23-2019, 07:13 PM Go to last post
  13. If you could only keep 1, which 1, why?

    Started by kolot, 03-22-2019 09:30 AM
    • Replies: 14
    • Views: 430
    03-23-2019, 06:35 PM Go to last post
  14. would you or wouldn't you

    Started by searcyfarms, 03-19-2019 04:31 PM
    • Replies: 14
    • Views: 566
    03-22-2019, 11:14 PM Go to last post
  15. Amazon flowmeter

    Started by steves08gxp, 03-21-2019 11:58 PM
    • Replies: 9
    • Views: 261
    03-22-2019, 04:48 PM Go to last post
  16. Spray Powder welding

    Started by Rod in MN, 03-22-2019 03:38 PM
    • Replies: 2
    • Views: 157
    03-22-2019, 04:07 PM Go to last post
  17. How much gas should I expect in a full bottle

    Started by WedingSir, 03-17-2019 11:16 PM
    • Replies: 10
    • Views: 411
    03-22-2019, 01:21 PM Go to last post
  18. Suitcase, or not to suitcase?

    Started by Q-Fab, 03-20-2019 11:37 AM
    2 Pages
    1 2
    • Replies: 29
    • Views: 766
    03-21-2019, 11:34 PM Go to last post
  19. Surface protection

    Started by bflmpsvz, 02-17-2019 02:31 AM
    • Replies: 8
    • Views: 636
    03-21-2019, 07:31 PM Go to last post
  20. Polishing aluminum pipe railings

    Started by outdoort, 03-17-2019 08:56 PM
    • Replies: 7
    • Views: 403
    03-21-2019, 09:21 AM Go to last post
  21. Ellis 1200 mitre band saw

    Started by kolot, 03-19-2019 05:56 PM
    • Replies: 18
    • Views: 425
    03-20-2019, 10:08 PM Go to last post

Forum Information and Options

Moderators of this Forum
Users Browsing this Forum

There are currently 325 users browsing this forum. (3 members & 322 guests)

  1. Milkerman,
  2. NathanDoty,
  3. Pcmaker

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
RSS | Home | Penton Media | Contact Us | Subscribe | For Advertisers | Terms of Use | Privacy Statement