Activity Stream - WeldingWeb - Welding Community for pros and enthusiasts

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums

34 Minutes Ago

Welder Dave replied to a thread smaw 1gf cwb test flat s- ticket in MIG, TIG, Stick, And Oxy/Fuel Welding

This should help. Strike ahead and bring the arc back to the crater. http://www.grbwelding.com/_CWB_Procedure_and_Rules.pdf

1 replies | 11 view(s)

37 Minutes Ago

smithdoor replied to a thread Roughneck 1E no power output need help in Miller

The Roughneck welders have slip rings. Since bend sitting 5 years the rings will have oxide and this will give no power. Simple to clean slip...

6 replies | 277 view(s)

43 Minutes Ago

smithdoor replied to a thread Non OxyAcetelyne Heat Sources for Brazing in General Welding Questions

I have one time used mapp gas and oxygen. One time has to used weld with propane and oxygen. The only reason I used mapp or propane is i had no...

12 replies | 184 view(s)

44 Minutes Ago

tapwelder replied to a thread Non OxyAcetelyne Heat Sources for Brazing in General Welding Questions

TIG brazing. Done it a few times. Last week fabbed a rail with custom ornaments. Used silicon bronze. Worked well, was wondering how the capillary...

12 replies | 184 view(s)

1 Hour Ago

RSH started a thread intro in Introduce Yourself

hello, former residential framer /carpenter house erector up to lock up, decks, railings, stairs, fences, basement developments ...etc. Some light...

0 replies | 5 view(s)

1 Hour Ago

G-ManBart replied to a thread Non OxyAcetelyne Heat Sources for Brazing in General Welding Questions

I'm no expert, but think TIG brazing works really well. I actually have some aluminum bronze rods on the way so I can try that option for TIG...

12 replies | 184 view(s)

1 Hour Ago

RSH started a thread smaw 1gf cwb test flat s- ticket in MIG, TIG, Stick, And Oxy/Fuel Welding

hello, do welders recommend on stop/start (tie- in ) on square side for second bead ...... Option A reverse -t scratch in weld zone move quickly up...

1 replies | 11 view(s)

1 Hour Ago

psacustomcreations replied to a thread Scrap metal art or projects in Welding Projects & Pictures

Thank you for the kind words. Here are a few questions I would throw out for you to think about. Are you looking at crafts or more towards fine...

2505 replies | 367963 view(s)

2 Hours Ago

Lis2323 replied to a thread Show us what you welded today in Welding Projects & Pictures

Sent from my iPhone using Tapatalk

12410 replies | 3169765 view(s)

2 Hours Ago

Welder Dave replied to a thread Weld cracking in dissimilar steels in MIG, TIG, Stick, And Oxy/Fuel Welding

It's a U groove (double J groove) which is a type of narrow gap welding. Was more curious how the root was done.

63 replies | 2440 view(s)

2 Hours Ago

VaughnT replied to a thread Blacksmithing tools in Sticky Forum

Welding temp isn't a question of need so much as it is a natural byproduct. Even the smallest forge should be able to reach welding temps if you...

1918 replies | 166521 view(s)

2 Hours Ago

Lis2323 replied to a thread Scrap metal art or projects in Welding Projects & Pictures

The bottom photo is an extremely cool perspective IMO. Sent from my iPad using Tapatalk

2505 replies | 367963 view(s)

3 Hours Ago

Shootr replied to a thread Scrap metal art or projects in Welding Projects & Pictures

I really try to eliminate the emotional part of making the piece (creator complex lol?) when I take a stab at pricing stuff. In a gallery or having...

2505 replies | 367963 view(s)

3 Hours Ago

Reebz replied to a thread Scrap metal art or projects in Welding Projects & Pictures

PSAcustomcreations this thread has been very inspiring to me, so much so I'm getting out of some of the gym equipment and moving into art/furniture....

2505 replies | 367963 view(s)

3 Hours Ago

Broccoli1 replied to a thread Miller Multimatic 220, question about 120v operation in Electrical

"Can I put that 50 amp receptacle on a 30 amp circuit or do I really need to go for the heavier gauge wire and bigger breaker and everything?" ...

2 replies | 49 view(s)

3 Hours Ago

psacustomcreations replied to a thread Scrap metal art or projects in Welding Projects & Pictures

What would you price it as an art piece or sculpture? What would you price it as a clock? I have an idea of my prices, but am curious of your...

2505 replies | 367963 view(s)

3 Hours Ago

MinnesotaDave replied to a thread Yesterday afternoon I taught myself to mig aluminium. in MIG, TIG, Stick, And Oxy/Fuel Welding

Are you welding in spray or short circuit? Spray transfer is what you want for aluminum mig. Also as mentioned above, push, not pull. ...

23 replies | 456 view(s)

4 Hours Ago

Gamble replied to a thread FS: Torches - tig, mig, stick in Shop, Trade, Sell Forum

give me your stimulus money :laugh:

16 replies | 817 view(s)

4 Hours Ago

Shootr replied to a thread Scrap metal art or projects in Welding Projects & Pictures

I can see a clock being more practical, and if doesn't sell as it is - I may go ahead and submit - but it's ART maaaaaann! :laugh:

2505 replies | 367963 view(s)

4 Hours Ago

Josey replied to a thread Another Wheel in Welding Projects & Pictures

Split the nut the old fashioned way. A sharp cold chisel and a block hammer. Has worked for me many times sometimes the impact will...

150 replies | 9213 view(s)

4 Hours Ago

tapwelder replied to a thread Non OxyAcetelyne Heat Sources for Brazing in General Welding Questions

Propane will limit ones ability of learning to braze. It is not thw best for building io filler or running beads.

12 replies | 184 view(s)