FS: Miller shop clean out!

[jontheturboguy]

WHO: Jeff Etter
WHERE: Franklin Indiana
CONTACT: 317-695-four three three 6.
WHAT: Listed below

I have several of Jeff's machines here at the shop. Some of them are in perfect working order, some need some small repairs done to them. Feel free to contact me via PM / Email or simple call Jeff and make an offer.

1.) First up is a pair of Miller Thunderbolt XL AC stick welders. Units appear to have very low run time, are complete, and work. They have been blown out and the hoods washed.
$250 ea


2.) Three steel chassis Miller Radiator-1 Tig Coolers. These units are as follows:
-Two complete units. They run and pump just fine. Need tanks washed out.
$300
-One is missing on / off switch and reservoir cap. Wired hot like a Benard unit - always on when welder is on. Pump locked up. Needs tank washed out.
$200


3.) Miller CP200 with Millermatic 10E Wire feeder
The feeder is missing a drive wheel. Other than that, appears complete. I do not have 3 phase in the shop so I can not test the unit. Appears complete inside. Comes with what appears to be a 300 amp Tweco gun assembly.
$350



4. Miller CP200 with Millermatic S-52E feeder. Feeder is missing a drive wheel and a relay inside is not hooked up. Other than that, appears complete. I do not have 3 phase in the shop so I can not test the unit. Appears complete inside. Comes with what appears to be a 300 amp Tweco gun assembly.
$350



5. Miller Coolmate 3 on plastic chassis. Unit is pretty clean. Pump needs a rebuild kit. Motor and pump will turn by hand, but is restrictive. A simple vein replacement would most likely do the trick.
$275



WHO: Jon Martindale
WHERE: Indianapolis Indiana
CONTACT: Please email or PM
WHAT: Listed below

1.) CP300 parts machine. Machine is very very clean. Missing face off front, and fan is in pieces.Either rebuild & restore, use for parts, or scrap.
$175


2.) Millermatic S-52E feeder, white face. Unit is in pieces, but complete. A "restoration" was started but never finished. Drive roll aluminum locking plate is cracked. Missing faces.
$100
*NO PICTURE*

3.) Bernard Stainless steel tig water cooler. Unit works and pumps. Been used in its life. Still has lot of service left to give.
$300


I do not care to ship Jeff's units or mine. However, if you setup shipping, Im sure either one of us will accommodate your needs. Be prepared for a palette & or crate charge. Our time is not free.

[jontheturboguy]

Hard files attached.

[jontheturboguy]

Hard files attached part two.

[Big65mopar]

We use the Bernard's pretty heavily in the shipyard on miller 300 / 350 synchro's and thermal arc 300's and they hold up really well to dust and grit and allot of use. Blow out the radiator with compressed air once a week and it'll work good.

[jontheturboguy]

Both migs gone.
Miller plastic tank cooler gone.

All other coolers, units, and parts still here.

Also have two PT-17A plasma torches still here with parts that go with them. They are demo units. Not new, but barely used. Make offer.

[jontheturboguy]

Bernard unit gone.

One older miller cooler gone...two coolers left. Ones locked up in the pump but is clean in appearance the other runs and pumps but drips out of shaft seal.

MAKE OFFERS.

Get this stuff out of my way!!!!!

[jontheturboguy]

Last chance for the cp300. Scrapping sunday. Off to the bone yard.

[jontheturboguy]

Make offers on the remaining stuff folks. Some one out there needs this stuff. Beyond tired of tripping over it. Winter is coming. I need sh@#@$t out of my way.

[porosity]

Make offers on the remaining stuff folks. Some one out there needs this stuff. Beyond tired of tripping over it. Winter is coming. I need sh@#@$t out of my way.

What's the deal with the wire feeder units? What power supplies are they compatible with?

[jontheturboguy]

What's the deal with the wire feeder units? What power supplies are they compatible with?

The only things I have left are:
-two older tig coolers. One is locked up. One runs but leaks. $400obo for the pair
-miller super s-32p suitcase $500obo
-the two miller stick welders $200 ea

[porosity]

Can the suitcase run with a CC power supply?

[jontheturboguy]

Yes it can

[krprice84]

How much wood that Bernard cooler cost to ship to Calgary Alberta? T2p 0T5 it's a business address but if res is cheaper T2Z 2V3

[jontheturboguy]

How much wood that Bernard cooler cost to ship to Calgary Alberta? T2p 0T5 it's a business address but if res is cheaper T2Z 2V3

The only things I have left are:
-two older tig coolers. One is locked up. One runs but leaks. $400obo for the pair
-the two miller stick welders $200 ea

Please read above....

[jontheturboguy]

Bump to the top