+ Reply to Thread
Results 1 to 12 of 12

Thread: widow maker

  1. #1
    Join Date
    Nov 2009
    Location
    Arizona
    Posts
    3,583
    Post Thanks / Like

    widow maker

    mason's 10" diamond wheel (PS no eye protection or respirator either)
    Miller Challenger 172
    Miller Thunderbolt AC/DC 225/150
    Miller Maxstar 150 STL
    Victor 100C
    Victor Journeyman
    Oxweld OA
    Harris O/A
    Smith O/A little torch

    No, that's not my car.

  2. #2
    Join Date
    Mar 2011
    Location
    Western Washington
    Posts
    10,549
    Post Thanks / Like

    Re: widow maker

    BTDT

    Very handy for doing faux rock work, takes a bit of getting used to the gyroscopic precession though

  3. #3
    Join Date
    Nov 2009
    Location
    Arizona
    Posts
    3,583
    Post Thanks / Like

    Re: widow maker

    It could make a real man out of ya......or not.
    Miller Challenger 172
    Miller Thunderbolt AC/DC 225/150
    Miller Maxstar 150 STL
    Victor 100C
    Victor Journeyman
    Oxweld OA
    Harris O/A
    Smith O/A little torch

    No, that's not my car.

  4. #4
    Join Date
    Mar 2011
    Location
    Western Washington
    Posts
    10,549
    Post Thanks / Like

    Re: widow maker

    LOL!!!!! yeah!!!! might do the opposite you really got to watch out for the things you do routinely... like sitting the grinder on the ground right after you're done with it!!!

  5. #5
    Join Date
    Dec 2018
    Location
    Southern California
    Posts
    1,127
    Post Thanks / Like

    Re: widow maker

    Widow/soprano maker!

  6. #6
    Join Date
    Mar 2011
    Location
    McGregor, Iowa
    Posts
    161
    Post Thanks / Like

    Re: widow maker

    I've got one really similar to that, A black and decker 9" with a 10" diamond blade on it. Only mine's worse, it has a on/off switch instead of a trigger. Cannot set it down at all until it stops spinning, the gyroscopic motion will make the grinder move on its own if its still spinning. It's the sweetest undercut/jamb saw there is though. Used it a lot to cut on foundations where I couldn't get the big and bulky concrete saw in place. Also indoors where gas powered equipment will smoke people out.

  7. #7
    Join Date
    Nov 2012
    Location
    new york city
    Posts
    6,918
    Post Thanks / Like

    Re: widow maker

    Quote Originally Posted by bigb View Post
    mason's 10" diamond wheel (PS no eye protection or respirator either)
    over the years i've seen plenty of guys using that setup. almost invisible behind a cloud of dust squinting to see WTH their cutting. no mask and no face-shield was de rigueur.
    i.u.o.e. # 15
    queens, ny and sunny fla

  8. #8
    Join Date
    Jul 2018
    Location
    Bay Area, CA
    Posts
    32
    Post Thanks / Like

    Re: widow maker

    I'm sure I do lots of stuff at work that would make those unfamiliar with the collision repair industry squeamish, but I gotta say no thanks on that grinder setup. I lost the knuckles off of a couple gloves before I threw out my old 4 1/2" grinder and bought one with a guard. I know there are situations when you've got to get in to a tight spot and the dangerous way is the only way, but i would lock that thing up for emergency use only.

  9. #9
    Join Date
    Oct 2014
    Posts
    5,270
    Post Thanks / Like

    Re: widow maker

    Good way to easily lose fingers or other appendages.

  10. #10
    Join Date
    Jun 2012
    Location
    Big Lake/Monticello MN
    Posts
    15,406
    Post Thanks / Like

    Re: widow maker

    I'm more concerned about lack of eye protection or dust mask...

    You know you might lose part of a hand and try to be careful, can't predict eye damage or keep away from dust.
    Dave J.

    Beware of false knowledge; it is more dangerous than ignorance. ~George Bernard Shaw~

    Syncro 350
    Invertec v250-s
    Thermal Arc 161 and 300
    MM210
    Dialarc
    Tried being normal once, didn't take....I think it was a Tuesday.

  11. Likes ronsii liked this post
  12. #11
    Join Date
    Oct 2014
    Posts
    5,270
    Post Thanks / Like

    Re: widow maker

    Should have eye protection for sure but the whole set up is an accident waiting to happen.

  13. #12
    Join Date
    Mar 2005
    Location
    Under a Rock
    Posts
    7,979
    Post Thanks / Like

    Re: widow maker

    Quote Originally Posted by Welder Dave View Post
    Should have eye protection for sure but the whole set up is an accident waiting to happen.
    A micro small piece of cement dust in your eye is very painful and irritating. Been there.
    Miller 211
    Hypertherm PM 45
    1961 Lincoln Idealarc 250
    HTP 221


    True Wisdom only comes from Pain.

+ Reply to Thread

Quick Reply Quick Reply

Register Now

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

A) Welding/Fabrication Shop
B) Plant/Production Line
C) Infrastructure/Construction/Repair or Maintenance/Field Work
D) Distributor of Welding Supplies or Gases
E) College/School/University
F) Work Out of Home

A) Corporate Executive/Management
B) Operations Management
C) Engineering Management
D) Educator/Student
E) Retired
F) Hobbyist

Log-in

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Page generated in 1,713,295,904.48713 seconds with 18 queries