-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Originally Posted by
ronsii
LOL!!!! 'A touch' yeah, I've told people just a tiny bit of ether will help... they call up a few hours later telling me how it's almost running and it'll 'run on ether' -- so I show up and there's 3-4 empty cans of ether on the ground and two sets of jumpers running to the batteries...
Yeah, I've seen that too. I guess you just have to know what's going on. One other thing I've seen with diesels that have done a lot of sitting is fuel racks in the pump stuck in the stop position (or full fuel in 2 stroke Detroits), I cant say on the op's engine, because I have no experience with those. But it is a possibility.
-
-
Post Thanks / Like - 1 Likes, 0 Dislikes
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Perkins can be a little finicky to bleed but talked to an experienced mechanic who said a a small shot of ether after hand priming with no bubbles wouldn't hurt. Small shot is 1 second not 1 can. A lot of people don't pump the hand primer enough. After the bubbles are gone you need to pump about 20 times more.
-
Post Thanks / Like - 1 Likes, 0 Dislikes
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Originally Posted by
Welder Dave
Perkins can be a little finicky to bleed but talked to an experienced mechanic who said a a small shot of ether after hand priming with no bubbles wouldn't hurt. Small shot is 1 second not 1 can. A lot of people don't pump the hand primer enough. After the bubbles are gone you need to pump about 20 times more.
Believe me, I pumped it like it owed me money. I haven't gotten back to it yet. Battery is charged though, so I will probably fool with it again sometime this week. Going to bleed the injectors just to be sure I've gotten all the air out.
-
Post Thanks / Like - 1 Likes, 0 Dislikes
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
I have one of these there is a real fine screen in the sediment bowl MAKE sure it is clean there is also another screeen in or by the electric fuel pump you have to take out a small Phillips screw in the middle of the lid there is a Oring a small one my experience has taught me to change that oring they leak and makes it hard to prime
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
I finally got back to it and made a little progress. Bled the injector pump and fuel filter again, just to be sure. Then I bled the injectors, twice. Stale diesel really has a stench of it's own. The lines were full of air and stale diesel. Then I started cranking. It started puffing a little more, and a little more, and a little more, then a lot, then it finally hit a good lick, caught, and would have run on it's own if I'd held the button down another half a second. Mashed it again, it popped right off and ran. Oil pressure gauge showed close to 80 psi oil pressure, which dropped a little as it started warming up. Blew a whole lot of garbage out of the exhaust pipe. I didn't run it long, but did run it long enough to figure out it isn't charging the battery, the idler isn't working, there's no welding current output, and no auxiliary AC output. Also not sure if the temp gauge or sending unit are any good. Engine felt warm enough that the gauge should have registered, but it never moved.
The commutator and AC slip rings are clean. The brushes are all in very good shape and making good contact. I'm suspecting that either the oil pressure switch is bad, or the alternator is bad, or both. I assumed it was the alternator last night and so took the existing Prestolite unit off. Bought a one wire Delco to replace it for $60 or so. Didn't get it on last night, so I spent some time reading up while the wife was gone this morning getting groceries. That lead me to wondering if a bad oil pressure switch might have caused all the problems rather than just some of them. Also wondering if I should check the reed switch. The panel that the welding lugs are connected to is somewhat bent. It's bent enough that it might have damaged the reed switch.
Originally Posted by
Leogl
I have one of these there is a real fine screen in the sediment bowl MAKE sure it is clean there is also another screeen in or by the electric fuel pump you have to take out a small Phillips screw in the middle of the lid there is a Oring a small one my experience has taught me to change that oring they leak and makes it hard to prime
Sediment bowl is brand new. The old one kept clogging when I was trying to drain the tank, plus it started leaking after I took it apart repeatedly. No electric fuel pump. This one has a four bolt mechanical lift pump with a manual primer arm.
-
Post Thanks / Like - 1 Likes, 0 Dislikes
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Glad to hear you've got it running.
My two cent would be to focus on finding the problem with the welding section and when that's fixed work on the alternator and auto idle (reed switch etc).
Since you question the temperature gauge carefully monitor the temp during testing.
Check wiring diagram for your machine for fuses or circuit breakers.
Next since you don't have AC output, flash the fields. Search the net for instructions or a service manual if you can find one.
Next would be testing the field diode bridge. Again net search or manual.
Keep us posted and good luck.
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Originally Posted by
KC51
Glad to hear you've got it running.
My two cent would be to focus on finding the problem with the welding section and when that's fixed work on the alternator and auto idle (reed switch etc).
Since you question the temperature gauge carefully monitor the temp during testing.
Check wiring diagram for your machine for fuses or circuit breakers.
Next since you don't have AC output, flash the fields. Search the net for instructions or a service manual if you can find one.
Next would be testing the field diode bridge. Again net search or manual.
Keep us posted and good luck.
I have a service manual(for a slightly newer machine though), IM407, and a Perkins manual. There's no schematic on either of the doors, and I'm not 100% certain the schematic in IM407 is correct. It appears to be. Only fuse I could find was good. The bridge rectifier is good, but I may swap it anyway. Going to email lincoln and see if they'll send me the correct schematic.
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Just got some schematics from Lincoln. Looks like my suspicion was right and I need to at least check the oil pressure switch. Alternator went to the repair shop today, so that's getting ruled out. Ordering a new pressure switch today.
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Alternator repair guy said it was in bad shape, but got it rebuilt and back to me today. Put it back on this evening. Charging problem is solved and the oil pressure switch is good. Still no welding current, no AC, and the idler isn't working.. I flashed the AC side per the instructions Lincoln sent me. Still got no AC.
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Glad you're making some progress.
Was the fuse you checked on one of the AC wires feeding the bride rectifier?
I'd suggest following the troubleshooting guide in the service manual you have. It may not be for your exact machine but should be close.
After flashing with no AC output test for problems with the welding alternator(exciter).
-
Post Thanks / Like - 1 Likes, 0 Dislikes
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Originally Posted by
KC51
Glad you're making some progress.
Was the fuse you checked on one of the AC wires feeding the bride rectifier?
I'd suggest following the troubleshooting guide in the service manual you have. It may not be for your exact machine but should be close.
After flashing with no AC output test for problems with the welding alternator(exciter).
Yep, the one on the back side of the control panel, right beside the bridge rectifier. Everything that I could test with a meter has been tested, either before I put everything back together or since. I guess I will pull everything apart again and start over.
-
need help with lincoln Ranger 250
I have a Lincoln Ranger 250 I have got trouble with it when you start it if it goes to a idle it will weld but when you change rod it will not weld again until you kill the machine and start it and it goes back to a idle then you can weld again I though it may be the PC Board but never had this to happen before. anyone have any ideals
-
Re: need help with lincoln Ranger 250
Getting 0.6 volts at the welding lug terminals and 1 volt to 1.6 volts from the 115v outlets. Talking to a tech at Lincoln. Maybe I'll get it sorted out. If not, I bet I can get more than $400 out of the engine.
-
Re: need help with lincoln Ranger 250
Well, just got off the phone with Bob Crow at Lincoln. Looks like the armature is shorted. Gonna call around and see if anyone has a good used one or has recommendations on a rewind service.
-
Re: need help with lincoln Ranger 250
Sorry to hear that.
I had the same situation several years ago and was lucky enough to find a parts machine.
I used Eurton to rewind an exciter armature several years ago and at that time they listed main armature rewinding on their website. I don't see it now but worth a call
https://eurtonelectric.com/catalog/armatures/lincoln
Bob Crow is a class guy. I think formally retired but still helps out.
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Thread got hijacked with a new title. I put the title back to the way it was using the Advanced Reply. Will see if that sticks.
Century buzzbox that I learned on 40+ years ago (was Dad's)
Crappy Century 110volt mig 70 amp pigeon pooper.
Lincoln Idealarc TIG-300
-
Re: need help with lincoln Ranger 250
Originally Posted by
KC51
Sorry to hear that.
I had the same situation several years ago and was lucky enough to find a parts machine.
I used Eurton to rewind an exciter armature several years ago and at that time they listed main armature rewinding on their website. I don't see it now but worth a call
https://eurtonelectric.com/catalog/armatures/lincoln
Bob Crow is a class guy. I think formally retired but still helps out.
Ditto on Bob Crow.
Eurton is my go to for rewinds. Shoot John Buchanan an email (john@eurtonelectric.com) and he'll give you a quote in short order.
MM200 w/Spoolmatic 1
Syncrowave 180SD
Bobcat 225G Plus - LP/NG
MUTT Suitcase Wirefeeder
WC-1S/Spoolmatic 1
HF-251D-1
PakMaster 100XL
'68 Red Face Code #6633 project
Star Jet 21-110
Save Second Base!
-
Post Thanks / Like - 1 Likes, 0 Dislikes
-
Re: need help with lincoln Ranger 250
Thanks for the info. Bob said he was retired, but still came in a couple of days a week to help out with the older machines.
Originally Posted by
duaneb55
Ditto on Bob Crow.
Eurton is my go to for rewinds. Shoot John Buchanan an email (john@eurtonelectric.com) and he'll give you a quote in short order.
Will email him. Thanks for the info.
-
Re: need help with lincoln Ranger 250
Got another armature(used). Pressure washed the machine a few days ago to get all the grime off. When I was washing it, it occurred to me that the grime around the welding generator looked an awful lot like the rear main seal had been leaking. Made me wonder if that was what shorted it. Waiting until I have the rest of the parts I plan on replacing before I separate it. It has some blow by, and since there's no hour meter, I'm debating whether to do a full rebuild while it's out.
-
Re: need help with lincoln Ranger 250
Took the Lincoln to work(overhead hoist for the win) a couple days ago and have been working on it here and there when the boss is out of paying jobs for me. Got it split yesterday and pulled the old armature off. Confirmed leaking rear main seal. Also popped the valve cover off and set the valve lash. Going to pick up some miscellaneous stuff today along with a new thermostat. Maybe by the end of the day Monday I'll have it all back together and welding.
-
Re: need help with lincoln Ranger 250
Got it all put back together. It runs and welds now. Haven't had time to check OCV or voltage at the outlets.
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
Hi machinisttx,
Did you ever get your machine welding?
Hey I need to re-wire my oil pressure switch on my Sa 250 and am having a hard time figuring out where the 2 wires go to coming off of the pressure sensor. The schematic I printed off is very confusing. Did you figure out the correct way to wire yours?
Thanks in advance
-
Re: Just saved a SA-250 D3 152 from the scrapyard, need some help with it
You can pressure wash the bottom of the tank.
-
Re: need help with lincoln Ranger 250
Originally Posted by
machinisttx
Took the Lincoln to work(overhead hoist for the win) a couple days ago and have been working on it here and there when the boss is out of paying jobs for me. Got it split yesterday and pulled the old armature off. Confirmed leaking rear main seal. Also popped the valve cover off and set the valve lash. Going to pick up some miscellaneous stuff today along with a new thermostat. Maybe by the end of the day Monday I'll have it all back together and welding.
you got lucky. I paid $1k for a 2000 model that was supposed to be a somewhat easy fix. Well, it probably would have been if he hadn't worked on it . $2500 more dollars later.....
Sent from my SM-N975U using Tapatalk
-
Re: need help with lincoln Ranger 250