Looking for a Pattern torch setup willing to travel a little

[Joegreen02]

Victor or heath brand is what I have seen. I’m looking for either a pattern or pantograph torch setup. Irish used to have a sharp little write up in how to build one. If some has that I’ll take it too. Thanks

Joe

[smithdoor]

I have owned both
They came with magic rotors
I this 1/4" & 1/2"
The 1/2" work the best.
As get older you have recharge the magic.
The magic rotors like 3/8 or 1/2" plate patterns.
I found for one off part I used plywood, paper clip and rubber bands.
1) Plywood for the pattern
2) paper clip and magic rotor,
3) rubber band an paper
4) pull and rubber band to keep the rotor, to the wood pattern.

If you in Clovis California I could just stop by.
It is very simple I think book just made bad.

Dave

Victor or heath brand is what I have seen. I’m looking for either a pattern or pantograph torch setup. Irish used to have a sharp little write up in how to build one. If some has that I’ll take it too. Thanks

Joe

[Joegreen02]

I’m in south Texas. Close to Corpus Christi actually.


Sent from my iPhone using Tapatalk

[thegary]

Victor or heath brand is what I have seen. I’m looking for either a pattern or pantograph torch setup. Irish used to have a sharp little write up in how to build one. If some has that I’ll take it too. Thanks

Joe

I have one that works fine and also has a setup to use a plasma torch . PM me for more info and I can send you pics if you give me a cell number or an email address. I retired last year and hove no need for it anymore. The only bad part is I am in Wisconsin. I might be traveling to the RGV in January or february . Key word is Might. I have 3 or 4 different diameter tracing tips for it and it has a cutting table that clamps to the vertical column. It could use new axy/fuel lines but they do not leak the way they are.

[Joegreen02]

I have one that works fine and also has a setup to use a plasma torch . PM me for more info and I can send you pics if you give me a cell number or an email address. I retired last year and hove no need for it anymore. The only bad part is I am in Wisconsin. I might be traveling to the RGV in January or february . Key word is Might. I have 3 or 4 different diameter tracing tips for it and it has a cutting table that clamps to the vertical column. It could use new axy/fuel lines but they do not leak the way they are.

I would definitely be interested in checking it out. That’s a jog up there lol. My number is (956) 551-1952 if you want to shoot some pics.


Sent from my iPhone using Tapatalk

[thegary]

I would definitely be interested in checking it out. That’s a jog up there lol. My number is (956) 551-1952 if you want to shoot some pics.


Sent from my iPhone using Tapatalk

I will take some pics tomorrow. It would be cheeper to ship it than for you to come up and get it. I have heard that speedy delivery charges by the pallet rather than weight. I would guess it could be shipped by speedy if I took it apart and put it on a pallet pretty reasonably

[Joegreen02]

That would be ideal. I’m not familiar with shipping via freight. I’ll make some calls tomorrow as well.


Sent from my iPhone using Tapatalk

[smithdoor]

I am only 1,400 miles away.
Just everyone here is at less a days drive from where at.
The good news most information we do via posts.

One biggest thing is everything needs to be leave with that torch.
Start first time on horses that was ok
Then I built a table that had concrete footings in the ground that could leave from time to time. That work great
How big is yours?

Dave

I’m in south Texas. Close to Corpus Christi actually.


Sent from my iPhone using Tapatalk

[Bob]

Dangit Joe, your timing sucks. I just gave away an Airco Camograph #42 with the table just a couple weeks ago and I'm a lot closer to you.

[Joegreen02]

Dammit bob. Next time wait a little longer lol. Yeah we are having a hell of a finding a reasonable shipper. I’ve almost got the wide convinced we should just clear the flat bed off and take a trip up.


Sent from my iPhone using Tapatalk