Results 1 to 7 of 7

Thread: Sm1 and wc-1 to mm200

  1. #1
    Join Date
    Dec 2014
    Location
    sw minnesota
    Posts
    46
    Post Thanks / Like

    Sm1 and wc-1 to mm200

    Ok I have a mm200 with the 14 pin plug I also have a wc1 and spoolmatic 1. My question is how Hook them all together to work properly?

  2. #2
    Join Date
    Sep 2016
    Location
    Detroit, Michigan
    Posts
    868
    Post Thanks / Like

    Re: Sm1 and wc-1 to mm200

    Quote Originally Posted by K98dkmauser View Post
    Ok I have a mm200 with the 14 pin plug I also have a wc1 and spoolmatic 1. My question is how Hook them all together to work properly?
    Did you look at the manuals available on Miller's website? They vary a bit with serial number, but most things don't change. With the MM200 there will be a difference between those with the 14 pin and earlier versions with a 5-pin.

    https://www.millerwelds.com/files/ow...O1210J_MIL.pdf
    Check out my bench vise website:
    http://mivise.com


    Miller Syncrowave 250DX
    Millermatic 350P with XR AlumaPro
    Miller Regency 200 with 22A feeder and Spoolmatic 3
    Hobart Champion Elite
    Everlast PowerTig 210EXT

  3. #3
    Join Date
    Dec 2014
    Location
    sw minnesota
    Posts
    46
    Post Thanks / Like

    Re: Sm1 and wc-1 to mm200

    The manual is kinda vague on how to install the wc-1 to power source. Do I use the 14 pin plug on the mm200 and use 115 volt ac from the Wall ? And I also don't have any of the cables for the wc-1

  4. #4
    Join Date
    Dec 2014
    Location
    sw minnesota
    Posts
    46
    Post Thanks / Like

    Re: Sm1 and wc-1 to mm200

    The serial number on the wc-1 is jh230958
    It has a 3 prong Hubbell plug on the back and a 2 prong female Hart lock plug.

  5. #5
    Join Date
    May 2008
    Location
    Orange, TX
    Posts
    17,387
    Post Thanks / Like

    Re: Sm1 and wc-1 to mm200

    Download the later WC-1 manual o1210j and install a 14-pin plug on the control cables of your earlier WC-1 to match the arrangement shown in the later wiring schematic. You will only need 4 of the 5 conductors of the earlier version eliminating the one shown going to the wide slot of RC2.
    MM200 w/Spoolmatic 1
    Syncrowave 180SD
    Bobcat 225G Plus - LP/NG
    MUTT Suitcase Wirefeeder
    WC-1S/Spoolmatic 1
    HF-251D-1
    PakMaster 100XL
    '68 Red Face Code #6633 project
    Star Jet 21-110

    Save Second Base!

  6. #6
    Join Date
    Dec 2014
    Location
    sw minnesota
    Posts
    46
    Post Thanks / Like

    Re: Sm1 and wc-1 to mm200

    I think the transformer is shot I have power going to it but nothing coming out.

  7. #7
    Join Date
    Dec 2014
    Location
    sw minnesota
    Posts
    46
    Post Thanks / Like

    Re: Sm1 and wc-1 to mm200

    Duane55 would know what transformer I would need to get as a replacement?
    I haven't had much luck finding parts for the wc-1.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Page generated in 1,623,657,792.32081 seconds with 13 queries