Results 1 to 14 of 14

Thread: Fencing question

  1. #1
    Join Date
    Nov 2005
    Location
    Nashville, TN
    Posts
    4,205
    Post Thanks / Like

    Fencing question

    Building a fence. The fence is 110 feet long it will be mounted atop a wall. The wall is pitched at 0.8 degrees or Approx 1 inch per 6 feet. A difference of approximately 1.5 ft drop over the run.

    It this pitch significant and visible in fencing. The panels are 6 ft built square. Question: Should I stagger them an inch or run the panels even across the top.

    The pitch in not visible when looking at the wall.

  2. #2
    Join Date
    Oct 2014
    Posts
    3,711
    Post Thanks / Like

    Re: Fencing question

    I see sound barrier fences along freeways and to me they look stupid because they will have maybe 20ft. at one height and then the next 20ft. at a lower height to follow the ground. It's personal preference but I think the top following the ground and being smooth would look better. On your fence, if it isn't noticeable looking at the wall, maybe you could make the fence so it corrects the drop/pitch and is horizontal across the entire length?

  3. #3
    Join Date
    Sep 2005
    Location
    Cave Creek AZ
    Posts
    3,253
    Post Thanks / Like

    Re: Fencing question

    Make it straight, nobody will notice an inch and a half in 110 feet.

  4. #4
    Join Date
    Nov 2005
    Location
    Nashville, TN
    Posts
    4,205
    Post Thanks / Like

    Re: Fencing question

    1.5 foot over 110 ft. Or .62 inch gap between the plumb vertical post and a horizontal top rail connection.

    This decision dictate the number / length of finished panel I install.

    I will get to experimenting.

    This is a recreation if some existing fencing. The existing fencing is old and ratty. May also get replaced.

  5. #5
    Join Date
    May 2007
    Posts
    3,496
    Post Thanks / Like

    Re: Fencing question

    i think it would be noticable if its a typical fence of vert pickets spaced about 4". if top rail was 1.5 sq tube, i wouldnt bring every panel up 1" every 6'/panel, cuz i wouldnt like the .5" of horiz overlap look at all. if u brought up every other panel, a .5" alignment gap between horiz rails - that would look better i think. might even go more than two panels.. i wouldnt want to hang my own fence outa plumb/level, and have to look at it every day knowing, and have done it on purpose . even if i couldnt see, it, it'd bother me
    Last edited by 123weld; 06-14-2021 at 11:22 PM.

  6. #6
    Join Date
    Sep 2014
    Posts
    1,742
    Post Thanks / Like

    Re: Fencing question

    You cannot put a pipe clamp on a diagonal and make them into a parallelogram? That would fix everything.

    Sincerely,

    William McCormick
    If I wasn't so.....crazy, I wouldn't try to act normal, and you would be afraid.

  7. #7
    Join Date
    Nov 2005
    Location
    Nashville, TN
    Posts
    4,205
    Post Thanks / Like

    Re: Fencing question

    I was wondering if it would form a natural parallelogram when it sags. I will set it up in my shop soon and see the difference.

  8. Likes William McCormick liked this post
  9. #8
    Join Date
    Nov 2005
    Location
    Nashville, TN
    Posts
    4,205
    Post Thanks / Like

    Re: Fencing question

    ??? ???

  10. #9
    Join Date
    Sep 2014
    Posts
    1,742
    Post Thanks / Like

    Re: Fencing question

    Quote Originally Posted by tapwelder View Post
    I was wondering if it would form a natural parallelogram when it sags. I will set it up in my shop soon and see the difference.
    How did it go?

    Sincerely,

    William McCormick
    If I wasn't so.....crazy, I wouldn't try to act normal, and you would be afraid.

  11. #10
    Join Date
    Nov 2005
    Location
    Nashville, TN
    Posts
    4,205
    Post Thanks / Like

    Re: Fencing question

    In the shop, no decernable visual difference. The bubble does touch the line when the rail is offset.

    Ultimately in was trying to determine the length panel I could preassemble and how/where to connect them without welding.

    Ironically this fence is around the corner from a gate I replaced years ago. Where some drunk took the gate danced with and laid out in the street with it, then disappeared with the gate. The gate was found about 3 yrs later in a neighbors tree.

    I guess next question is security bolts for concrete?

  12. Likes William McCormick liked this post
  13. #11
    Join Date
    May 2011
    Posts
    489
    Post Thanks / Like

    Re: Fencing question

    Security bolts.... nah.... just use a stainless epoxy all thread in 1 hole and gall the nut. Best security you can get.

    Sent from my SM-G960U using Tapatalk

  14. #12
    Join Date
    Dec 2013
    Location
    Mount Tabor VT
    Posts
    7,605
    Post Thanks / Like

    Re: Fencing question

    I use a level, then stand back & look at it. In some cases it looks awful! I mounted a meter socket, & service riser on an old house 6" out of plumb in 10'. I first mounted it plumb, it looked terrible! I then mounted it parallel to the building corner, that was better but wrong! I settled for splitting the difference, It was best in that situation.

    A fence near level but straight wants to parallel the ground. If it traverses steep or a mixture of pitches, mount panels level, correct for grade at each post.
    An optimist is usually wrong, and when the unexpected happens is unprepared. A pessimist is usually right, when wrong, is delighted, and well prepared.

  15. Likes William McCormick liked this post
  16. #13
    Join Date
    Nov 2005
    Location
    Nashville, TN
    Posts
    4,205
    Post Thanks / Like

    Re: Fencing question

    Thanks. Should have results within the next week or two.

  17. #14
    Join Date
    Mar 2018
    Location
    Clovis California
    Posts
    2,727
    Post Thanks / Like

    Re: Fencing question

    Sounds like project 👍.
    You have fun keep the work and photos.

    Dave

    Quote Originally Posted by tapwelder View Post
    Building a fence. The fence is 110 feet long it will be mounted atop a wall. The wall is pitched at 0.8 degrees or Approx 1 inch per 6 feet. A difference of approximately 1.5 ft drop over the run.

    It this pitch significant and visible in fencing. The panels are 6 ft built square. Question: Should I stagger them an inch or run the panels even across the top.

    The pitch in not visible when looking at the wall.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Page generated in 1,627,399,144.91619 seconds with 14 queries