Another Mickey Mouse Grinder Holder

[Lis2323]

I needed an easily moveable grinder stand for my welding tables and this is what I came up with…











in retrospect it actually looks a little goofy....

[acourtjester]

that will work and last a long timeI'm sure it will be copied many time.

[Freebirdwelds]

I don't think it looks like Mickey at all. lol

[whtbaron]

.... maybe Minnie...

[smithdoor]

Maybe it is Mickey M. after fight with Mike T.

Dave

[MinnesotaDave]

I like it, drop in a hole and ready to go

[smithdoor]

I just set the grinder on weld table.
It is big and flat too.

Dave

.... maybe Minnie...

[Lis2323]

I like it, drop in a hole and ready to go

Thanks! That's the plan...






Sent from my iPhone using Tapatalk

[smithdoor]

Both Minnie and Mickey have the same birthday 🎂

Dave

.... maybe Minnie...

[whtbaron]

For a table with no holes, you could use the same design on a 20 lb magnet.

[Lis2323]

For a table with no holes, you could use the same design on a 20 lb magnet.

I went more than 50 years without a mag drill. Never even knew about them (and DC welders) until later in life.

Now that I finally have one and don’t “really” need one, I’m gonna drill holes.


Sent from my iPad using Tapatalk

[smithdoor]

I have use and own a mag drill since before 1970.
It is tool that sits a lot today but I can put on the work bench for drill and tapping hole.
I also use it for line boring backhoes and other earth moving equipment.

Very handy tool when need.

Dave

I went more than 50 years without a mag drill. Never even knew about them (and DC welders) until later in life.

Now that I finally have one and don’t “really” need one, I’m gonna drill holes.


Sent from my iPad using Tapatalk

[N2 Welding]

Simple yet very effective.

[ArcTan]

Only effective if the grinder has a guard.

[Lis2323]

Only effective if the grinder has a guard.

Those without a guard I hang off my pant's back pocket....


Sent from my iPhone using Tapatalk

[whtbaron]

Only effective if the grinder has a guard.

I have those Y shaped hooks that I use, and they will still work without the guard so these should as well. You just have to be very careful with the thin disks or they will break.

[Oldendum]

M-i-c-k-e-y ____ g-r-i-n-d

[whtbaron]

Here's a shot of the ones I pick up at Princess Auto when they're on sale for cheap. These are 10 lb magnets and they work "ok"... I'd hold out for 20 lb ones in the future though. The 10's won't hold the sawzall up if the batteries are attached. On the 4.5" grinders they work with either the guards on or off. Maybe Mickey just needs rabbit ears...

[smithdoor]

Looks good.
I did feild work and no place for tool hangers. About the only hanger I used was for stinger or mig gun. No more than a disk harrow for base and pipe for stand all so used latter or scaffold .

Dave

Here's a shot of the ones I pick up at Princess Auto when they're on sale for cheap. These are 10 lb magnets and they work "ok"... I'd hold out for 20 lb ones in the future though. The 10's won't hold the sawzall up if the batteries are attached. On the 4.5" grinders they work with either the guards on or off. Maybe Mickey just needs rabbit ears...

[Lis2323]

Here's a shot of the ones I pick up at Princess Auto when they're on sale for cheap. These are 10 lb magnets and they work "ok"... I'd hold out for 20 lb ones in the future though.

]

Maybe I should grab a couple of these..





Sent from my iPad using Tapatalk

[whtbaron]

I was looking at those... think the sale is over soon too...half price until April 24

[Lis2323]

I was looking at those... think the sale is over soon too...

I never got around to getting that $65 LED yard light with photocell.

Didn't feel like spending $30 on gas to save $15.


Sent from my iPhone using Tapatalk

[farmersammm]

I went more than 50 years without a mag drill. Never even knew about them (and DC welders) until later in life.

Now that I finally have one and don’t “really” need one, I’m gonna drill holes.


Sent from my iPad using Tapatalk

You really never know you need one..............until you need one. Handy, but in my shop tends to gather dust........until I need it

[whtbaron]

You really never know you need one..............until you need one. Handy, but in my shop tends to gather dust........until I need it

I think my shop dust needs one too...

"Didn't feel like spending $30 on gas to save $15."

I rarely get into Wpg to go to the store... I rely heavily on the free shipping . Just order 20 of them...

[Lis2323]

I think my shop dust needs one too...

"Didn't feel like spending $30 on gas to save $15."

I rarely get into Wpg to go to the store... I rely heavily on the free shipping . Just order 20 of them...

nope. If i order online they offer free shipping to my store. lol


Sent from my iPhone using Tapatalk